ASTM D3123 PDF

Flow of Low-Pressure Thermosetting Molding Compounds. Article no: STD- Edition: Approved: 9/1/ No of pages: 4. Replaces: ASTM D ASTM-D Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds – spiral flow; thermosets;; ICS Number Code Standard Number, ASTM D – 09(). Title, Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds.

Author: Tenris Meztitilar
Country: Tanzania
Language: English (Spanish)
Genre: Video
Published (Last): 14 June 2010
Pages: 218
PDF File Size: 13.94 Mb
ePub File Size: 12.18 Mb
ISBN: 217-1-71436-989-5
Downloads: 43592
Price: Free* [*Free Regsitration Required]
Uploader: Shakagami

ASTM D3123 – 09(2017)

Alternative methods of conditioning samples shall be mutually agreed upon between manufacturer and purchaser. Please first verify your email before subscribing to alerts. Are you sure you want to empty the cart? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Permission rights to photocopy the standard may also be secured from the ASTM website www. Subscription pricing is determined by: In addition the electronic files may d31223 be downloaded or distributed elsewhere over computer networks or otherwise. Too long a dwell time before transferring will cause erratic results.

Norma ASTM D()

Attempts to develop a full precision and bias statement for this test method have not been successful. They shall be stored for a minimum of 24 h at the standard laboratory temperature, before breaking the seal on the container. Proceed to Checkout Continue Shopping. You currently cannot view this content. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. D — 09 sufficiently accurate for determining transfer pressure.

  MAHALLUL QIYAM PDF

However, a few well-documented cases are recorded where differences in pot diameters, even within this listed range, have caused large differences in flow-length readings.

This time will vary with the compound under test. Need more than one copy? It is especially suited for those compounds used for encapsulation or other low pressure molding techniques. Conversion to SI units can readily be made by multiplying the flow length, in inches, by the appropriate conversion factor, Therefore, the force exerted by the plunger shall be measured by some means such as an accurately calibrated direct-reading force gage or proving ring.

NOTE 5—Preforms or pellets may be used if found necessary; however, flow length may be affected by their use. You may delete a document from your Alert Profile at any time. Enter your personal account email address to request a password reset: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

No items in cart. Read the spiral flow length directly from the molded specimen at the point of farthest continuous flow to the nearest 0. Note 1—There is satm known ISO equivalent to this test method. This standard is not included in any packages. September 1, 1 Updated ISO equivalency statement. NOTE 4—There axtm considerable evidence that the test is usable over a wider range of flow lengths, but this has not yet been confirmed by interlaboratory testing.

If you like to setup a quick demo, let us know at support madcad. The electronic file may not be reproduced in any way. Last previous edition approved in as D – 98 Measure the temperature in accordance with the procedures described in Practice D or by thermocouples attached to the mold and plunger. No further reproductions authorized. Remember me for one month. It involves the use ast, a standard spiral flow mold in a transfer molding press under specified conditions of applied temperature and pressure with a controlled charge mass.

  EUTROMBICULA ALFREDDUGESI PDF

Spiral Flow of Low-Pressure Thermosetting Molding Compounds1

D — 09 Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds1 This standard is issued under the fixed designation D; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Please first log in with a verified email before subscribing to alerts. It involves the use of a standard spiral flow mold in a transfer molding press under specified conditions of applied temperature and pressure with satm controlled charge mass. NOTE 3—Since the only commercially available molds are calibrated in inches, spiral-flow length will be reported in these units.

Typical examples are presses with pot diameters of Precision and Bias No further reproductions authorized. Because this test method does not contain a round-robin-based numerical precision and bias statement, it shall not be used as a referee test method in case of dispute.