Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Voodoolmaran Maurg
Country: Slovenia
Language: English (Spanish)
Genre: Career
Published (Last): 10 May 2016
Pages: 188
PDF File Size: 2.6 Mb
ePub File Size: 15.94 Mb
ISBN: 276-1-34597-536-1
Downloads: 42453
Price: Free* [*Free Regsitration Required]
Uploader: Grolmaran

Originally published as A — Last previous edition A — The following coatings astn be specied: A number in parentheses indicates the year of last reapproval. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.

ASTM A493 for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

The material shall also conform to the a4493 as to mechanical properties. Link to Active This link will always route to the current Active version of the standard. An electroplated copper coating is often used.

Current edition approved Jan. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The following lubricants may be specied: This abstract is a brief summary of the referenced standard.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

General Requirements for Delivery 4. For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to austenitic grades. Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in the asm of revision, the year of last revision.


Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

axtm ASTM does not give any warranty express or implied ashm make any representation that the contents of this abstract are accurate, complete or up to date. Such requirements may include, but are not limited to the following: NOTE 1—A typical ordering description is as follows: The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

The steel shall conform to the required chemical composition requirements. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. It is informational only and adtm an official part of the standard; the full text of the standard itself must be referred to for its use and application. Soap is generally used.

A superscript epsilon e indicates an editorial change since the last revision or reapproval. The SI equivalents are in parentheses and may be approximate.


Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The producer should be consulted when material is required to tensile strength ranges other than those specied. Material can be manufactured to tensile strength ranges other than those shown in Table 2. ICS Number Code The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0. This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. This standard has been approved for use by agencies of the Department of Defense. Historical Version s – view previous versions of standard.

All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. Packaging and Package Marking 9. Resistance to Intergranular Corrosion 8.